Made in USA
Made in USA
Hornady Unprimed Brass Rifle Cartridge Cases
90255-86281
At Hornady, brass is the foundation for what could be the most memorable shot of your lifetime. Extra time and care is taken in the creation of our cases, producing smaller lots that meet strict quality standards. Our cases offer reloaders excellent uniformity in wall thickness, weight and internal capacity. We measure for consistently tight wall concentricity and even run our cases through a pressure calibration test to ensure uniform case expansion during firing. Our cases allow proper seating of the bullet, not only in the case, but in the chamber as well. High quality brass contributes to consistent charges and pressures.
Tight Wall Concentricity
Concentricity helps to ensure proper bullet seating in both the case and the chamber of your firearm. Higher concentricity also aids in a uniform release of the bullet on firing, for optimal velocity and accuracy.
Uniform Case Wall Thickness
Benchrest shooters have long known that uniform case wall thickness is vital to accuracy. We manufacture to extremely tight tolerances to ensure this critical element is as consistent as possible.
More Reloads Per Case
We treat Hornady brass as the foundation for an accurate cartridge, not a commodity. Because we take greater care in its creation you’ll get more reloads from Hornady brass.
Consistent Weight And Capacity
Every single Hornady case, regardless of the lot in which it was produced, is virtually identical to other Hornady cases in the same caliber. For you, this means consistent pressures, velocity and accuracy —every time.
Brass Preparation
With bulk rifle brass you may sometimes notice a few case mouths are “out of round” or slightly dented below the shoulder. These imperfections occur in the final tumbling wash operation after the case mouth has been annealed. Brass manufacturers are aware of the case cosmetics and have worked to mitigate it, but due to equipment design, denting may still occur. Minor dents are normally removed in the first firing and will not affect case life or performance. On non-plated brass, you may also notice all the anneal stain might not be polished off, which may give the case neck a pinkish color. With some smaller caliber cases you may notice the case mouths to be slightly belled.
California Residents
Select Delivery Method:Shipping
Add The Essentials
Hornady V-Max 22 Caliber Rifle Bullets
Starline Unprimed Brass Rifle Cases 50ct Bag
Hornady V-Max 24 Caliber Rifle Bullets
Hornady Unprimed Brass Rifle Cartridge Cases
90255-86281
At Hornady, brass is the foundation for what could be the most memorable shot of your lifetime. Extra time and care is taken in the creation of our cases, producing smaller lots that meet strict quality standards. Our cases offer reloaders excellent uniformity in wall thickness, weight and internal capacity. We measure for consistently tight wall concentricity and even run our cases through a pressure calibration test to ensure uniform case expansion during firing. Our cases allow proper seating of the bullet, not only in the case, but in the chamber as well. High quality brass contributes to consistent charges and pressures.
Tight Wall Concentricity
Concentricity helps to ensure proper bullet seating in both the case and the chamber of your firearm. Higher concentricity also aids in a uniform release of the bullet on firing, for optimal velocity and accuracy.
Uniform Case Wall Thickness
Benchrest shooters have long known that uniform case wall thickness is vital to accuracy. We manufacture to extremely tight tolerances to ensure this critical element is as consistent as possible.
More Reloads Per Case
We treat Hornady brass as the foundation for an accurate cartridge, not a commodity. Because we take greater care in its creation you’ll get more reloads from Hornady brass.
Consistent Weight And Capacity
Every single Hornady case, regardless of the lot in which it was produced, is virtually identical to other Hornady cases in the same caliber. For you, this means consistent pressures, velocity and accuracy —every time.
Brass Preparation
With bulk rifle brass you may sometimes notice a few case mouths are “out of round” or slightly dented below the shoulder. These imperfections occur in the final tumbling wash operation after the case mouth has been annealed. Brass manufacturers are aware of the case cosmetics and have worked to mitigate it, but due to equipment design, denting may still occur. Minor dents are normally removed in the first firing and will not affect case life or performance. On non-plated brass, you may also notice all the anneal stain might not be polished off, which may give the case neck a pinkish color. With some smaller caliber cases you may notice the case mouths to be slightly belled.
California Residents